13 replies to this topic

[Darcon]

Hi All,

Should have thought of pulling out my camera when I started my install but only thought of it as I was finishing up lol

Pretty much I saw in a previous thread questions about what speakers fit the rear doors.

The factory speakers look about 5 1/4 but sit inside a similar plastic spacer that was used when installing the front splits.

However to fit 6 1/2" speakers piss off plastic all together and purchase a set of plastic spacers from super cheap for $21.

It takes a little bit of time to get exact right placement for all four screws to go nicely through metal but not to difficult 30mm + screws will be required and than bobs your uncle.

As for the tweeters I used a hole cutter on my drill and placed them similar to the location in the drivers door. I was a little worried the tweeter might be too close to the driver but to be honest it sounds fantastic.

pics coming soon

[Darcon]

[Darcon]

[Indelible]

before you srew the speaker to the door using a spacer make sure the magnet doesn't foul on the door hinge thingy that goes inside the door when closed as i had to space my fusion speakers further out then you did coz of the large magnets would stop door from closing.
but don't space them out too much otherwise door trim won't fit
,MATT

[Jman]

i had that issue, custom door pods in progress

[quachy]

im doin this atm too and got the issues with the magnet being too big that the door hinge touches

how big of a spacer did you use?

[MkIIGrandeG]

one of my door speakers stopped working. i was in the proces of taking trim off but got stuck on the door hinge. how do i get it off!!! once the screw is out?

cheers

[quachy]

MkIIGrandeG, on Mar 16 2010, 03:47 PM, said:

one of my door speakers stopped working. i was in the proces of taking trim off but got stuck on the door hinge. how do i get it off!!! once the screw is out?

cheers

i used this thread, (thanks charwie:D)
http://www.jzx100.co...?showtopic=6323


6th photo shows you how to take it off, push down with the screw, i was trying to pull out the lock thing, was stuck on this for a little while LOL

[MkIIGrandeG]

quachy, on Mar 16 2010, 01:25 PM, said:

i used this thread, (thanks charwie:D)
http://www.jzx100.co...?showtopic=6323


6th photo shows you how to take it off, push down with the screw, i was trying to pull out the lock thing, was stuck on this for a little while LOL

thanks!

[jzxtoy]

darkon, on Jan 15 2010, 06:38 PM, said:

Hi All,

Should have thought of pulling out my camera when I started my install but only thought of it as I was finishing up lol

Pretty much I saw in a previous thread questions about what speakers fit the rear doors.

The factory speakers look about 5 1/4 but sit inside a similar plastic spacer that was used when installing the front splits.

However to fit 6 1/2" speakers piss off plastic all together and purchase a set of plastic spacers from super cheap for $21.

It takes a little bit of time to get exact right placement for all four screws to go nicely through metal but not to difficult 30mm + screws will be required and than bobs your uncle.

As for the tweeters I used a hole cutter on my drill and placed them similar to the location in the drivers door. I was a little worried the tweeter might be too close to the driver but to be honest it sounds fantastic.

pics coming soon

Its better to use MDF as spacers and not plastic as they resonate and can make your speakers sound like poo.Just cut rings of mdf bigger than the speaker and big enough to clear your thingy in the door, then just get 'wing tip" metal screws.drill hole in mdf then screw them to your door,then screw speaker to mdf,obviously after you have cut the hole for the speaker.