Forum Advertisements
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
  |
 Boostcut on 0,7 bar? |
 Jul 14 2010, 05:57 AM
Post
#1
|
|
|
Lackey   Group:  MembersPosts: 10 Joined: 12-July 10 From: Norway Member No.: 2,924  |
Hi=)
I tried to Seach but i didnt find a thread like this:/ Its a 1jz-gte engine. I Have a Greddy boost controller, and when i try to turn up the boost, its just peaks up and goes strait back down to 0,7 bar and stays there! I really want 1 bar. Is it not possible unless i buy a aftermarket Ecu? Is this boost cut? 0.7 bar really? I thaught i could run 1 bar without problems? Easy Mods: - 3"Exhaust fomr turboes - HKS Air Intake - Blitz Front mounted Intercooler. Something else can stop the pressure? Or is it Boost Cut? If i turn off the controller, its 0,7 bar no problem. But if i turn it on and will run 0,9 bar, it goes up to 0,9 bar in 1 Secund and goes down to 0,7 and stays there after. Espen H. This post has been edited by Dubbster: Jul 14 2010, 06:00 AM |
 |
 
|
|
Jul 15 2010, 09:57 PM
Post
#2
|
|
|
Lackey Group: MembersPosts: 10 Joined: 12-July 10 From: Norway Member No.: 2,924 |
No one knows what pressure you can boost on a stock motor before it hits boost cut?
|
|
|
|
|
Jul 15 2010, 10:01 PM
Post
#3
|
|
|
Bagman  Group:  Paid SupporterPosts: 233 Joined: 20-July 09 From: Innisfail Member No.: 2,204 |
sounds like your ebc needs tuning, crank up the gain a bit, also make sure the ebc is installed correctly
|
|
|
|
|
Jul 16 2010, 12:06 AM
Post
#4
|
|
|
Lackey Group: MembersPosts: 10 Joined: 12-July 10 From: Norway Member No.: 2,924 |
QUOTE (Dropbear @ Jul 15 2010, 01:31 PM)  sounds like your ebc needs tuning, crank up the gain a bit, also make sure the ebc is installed correctly Whats ebc? and where is it? Yea, ill try more and less gain and see what happens (IMG:style_emoticons/default/smile.gif) |
|
|
|
|
Jul 16 2010, 06:48 AM
Post
#5
|
|
|
Bagman Group: Paid SupporterPosts: 233 Joined: 20-July 09 From: Innisfail Member No.: 2,204 |
QUOTE (Dubbster @ Jul 14 2010, 06:27 AM) Hi=) I tried to Seach but i didnt find a thread like this:/ Its a 1jz-gte engine. I Have a Greddy boost controller, and when i try to turn up the boost, its just peaks up and goes strait back down to 0,7 bar and stays there! I really want 1 bar. Is it not possible unless i buy a aftermarket Ecu? Is this boost cut? 0.7 bar really? I thaught i could run 1 bar without problems? Easy Mods: - 3"Exhaust fomr turboes - HKS Air Intake - Blitz Front mounted Intercooler. Something else can stop the pressure? Or is it Boost Cut? If i turn off the controller, its 0,7 bar no problem. But if i turn it on and will run 0,9 bar, it goes up to 0,9 bar in 1 Secund and goes down to 0,7 and stays there after. Espen H. Electronic Boost Controller Read the manual for your GReddy and adjust the calibration |
|
|
|
|
Jul 18 2010, 10:45 PM
Post
#6
|
|
|
Lackey Group: MembersPosts: 97 Joined: 3-November 08 From: Perth Member No.: 1,732 |
you sir have a boost leak somewhere.
|
|
|
|
|
Jul 19 2010, 12:47 AM
Post
#7
|
|
|
Lackey Group: MembersPosts: 10 Joined: 12-July 10 From: Norway Member No.: 2,924 |
QUOTE (parrott @ Jul 18 2010, 02:15 PM) you sir have a boost leak somewhere. Hm.. Cant find any.. |
|
|
|
| Google Bot |
Post
#
|
 Google Ads |
|
|
|
|
|
Forum Advertisements
| Lo-Fi Version | Time is now: 4th September 2010 - 03:06 PM |